The NC-2A is a carrier-based vehicle designed to provide external electric power to aircraft for pre-flight or maintenance purposes. It saw extensive service on the aircraft carriers of the U.S. Navy (including Essex / Oriskany, Midway, Forrestal, Kitty Hawk, Enterprise and Nimitz classes) from the late 1960s and until the late 1990s.
This 1:72 scale model kit, produced by F4Models (cat. # 7034), contains resin and photo etched parts to build one NC-2A vehicle.
For reference purposes, here are some historical photographs that show the NC-2A in action: photo; photo; photo; gallery (refer to image #2893).
Notes:
- The NC-2A unit was not a tractor; it was not designed to tow aircraft or ground support equipment.
- The rear wheels of the NC-2A are steerable, not the front ones.
- The A/S-37A-3 vehicle (see photograph), in use on the USN carriers since the early 2000s, is substantially different from the much earlier NC-2A and is not intended to be built from this kit. Consequently, this model kit is only suitable for the late 1960's through 1990's dioramas & aircraft and not suitable for the period from 2000 onward.
- This is not a copy of the Verlinden's kit; the Verlinden's kit had a number of inaccuracies in shape / geometry.
- This kit is only for modellers with experience and high level of skill.
- This kit production is very limited. Write directly for ordering.
The MD-3A is a purpose-built flight deck tractor. It saw extensive service on all aircraft carriers and large-deck amphibious ships of the U.S. Navy, starting from as early as 1962 and until the late 1990s. Apart from the aircraft towing and positioning, these vehicles were employed to start up aircraft jet engines. For this purpose many were fitted with gas turbine start units mounted in the rear.
This 1:72 scale model kit, produced by F4Models (cat. # 7008), contains resin and photo etched parts to build one MD-3A tractor.
Notes:
- The MD-3A tractors were seen with at least three different types of the jet aircraft start unit; the kit #7008 includes the type of start unit that was the most common.
- Compared with the older plastic and resin models of the MD-3A tractor, the kit #7008 features the following:
- Accurately shaped driver's compartment, with correct width (which is 36% of the real vehicle's overall width, whereas the older kits have it at 52% of the overall width), front and real walls.
- Accurately shaped front and rear wheels (which have twin tires on the real MD-3A, whereas the older kits contain single-tire rear wheels).
- Detailed jet aircraft start unit.
- A small number of MD-3A flight deck tractors were also employed on the Royal Canadian Navy's HMCS Bonaventure and on the Argentine Navy's Veinticinco de Mayo aircraft carriers.
- Somewhere in the mid 1990s the U.S. Navy started the process of upgrading the venerable MD-3A's with a newer version. This new tractor, designated as A/S32A-31A, differed from the original by having wider and slightly raised aft end, wider rear wheels and some other minor improvements. Having a different geometry, the A/S32A-31A variant is not intended to be built from this kit. Consequently, this model kit is only suitable for the 1960's through 1990's dioramas & aircraft and not suitable for the period from 2000 onward.
- This kit is only for modellers with experience and high level of skill.
- This kit production is extremely limited. Write directly for ordering.
This set (F4Models # 7035) contains metal photo-etched items to detail one WC-51 or WC-52 U.S. Military ¾ ton 4WD truck model.
Notes:
- This is a detail set and not a full kit. It is suitable to detail the 1:72 scale plastic model of the Dodge WC-51 / WC-52 truck produced by Italeri.
- This set is for modellers with experience and high level of skill; do not buy this set if you build your kits "out of the box" and use paint brush to hand-paint them.
- The production run was extremely limited, with only 10 sets produced. Write directly for ordering.
- The key items in this detail set are the radiator grille, the front fenders and the windshield, as the respective kit's plastic parts are unrealistically thick. Other small items are also included, such as the steering wheel, rear bumpers, jerry can holder and rearview mirrors. As this set is mainly intended for aircraft diorama builders and not for AFV modellers, it does not contain options to detail the items that, according to available historic photographs, were not used on airfield utility vehicles. In particular, the set contains no items to detail the crew weapons and respective holders / mounts.
- When building the Italeri model (as well as it's predecessors), do not forget to alter the suspension and drivetrain parts to lower the ground clearance, as the kit's parts, if used "out of the box", will give the model a totally unrealistic "big foot" appearance.
